Aesthetic Classroom · Smartboard Timer
👆 Name this activity
05:00

Scroll for guide & context

Smartboard Timer

A smartboard timer is used differently from a timer on a laptop. You stand at the board, you use your finger instead of a mouse, and the class watches every tap. There is often no keyboard within reach. So the questions that matter are about touch: what you can tap, what happens when a tap does nothing, and how the board behaves while the countdown runs.

Two kinds of board, one page

"Smartboard" usually means one of two things. An interactive whiteboard is a touch surface with a projector that shines the image onto it. An interactive flat panel is a large touchscreen, often with its own built-in computer and browser.

This timer runs in a web browser, so it works on both. You can open it in two ways:

  • In the board's built-in browser, if your panel has one. Touch goes straight to the page.
  • On the computer connected to the board. The board shows the computer's screen and sends your touches to it as mouse clicks.

There is nothing to install and no account. Type the address once, then save it as a bookmark in the browser you use on the board.

What you can tap, and how big it is

The buttons under the timer are sized for fingers. The −, reset and + buttons are 44 by 44 CSS pixels, and Start is wider. That matches the 44-pixel size in the Web Content Accessibility Guidelines (WCAG), success criterion 2.5.5, the strictest level for touch targets.

On a large board, a CSS pixel is bigger than on a laptop. A 75-inch panel is about 166 cm wide. If the browser shows 1920 CSS pixels across it, each one is a little under 1 mm, and a 44-pixel button is about 3.8 cm wide. That is easy to hit with a finger, even at arm's length.

The preset tabs at the top are the smallest targets on the page. They are text labels, not large buttons. Tap the middle of the label. If a tap lands on the wrong length, it does no harm: tap the right one, or use − and + to change the time by one minute.

The disc itself is not a control. You cannot drag it to set a time. It only shows the time left.

When a tap does nothing

Most touch problems on a board come from the board, not from the page. Check these in order:

  1. Pen or annotation mode is on. Many boards have a mode where a touch draws ink on the screen instead of a click. Switch back to touch or mouse mode.
  2. The projected image is out of line. On a projector board, if taps land a few centimeters away from your finger, the board needs to be calibrated again. Use the board's own calibration tool.
  3. Another window is on top. A floating toolbar or a notification can catch the tap. Close it, then tap the timer again.

When I first tested this page on an interactive panel in a university teaching room, my first three taps drew red lines across the timer. The pen mode was still on from the previous lecture. It took me a minute to see it, with the room watching. Now the first thing I do at an unfamiliar board is one test tap on an empty part of the screen.

Make the timer big enough for the back row

On a board, the timer should fill the screen, not share it with a browser bar and bookmarks. Tap the fullscreen button in the bottom-right corner. Tap it again, or press Esc, to leave fullscreen.

Some built-in browsers on interactive panels do not support fullscreen for web pages. If the button does nothing, use the board's own setting to hide the browser bar, or open the page on the connected computer instead.

The disc is the largest part of the timer, up to 240 CSS pixels across. On the 75-inch panel above, that is about 20 cm. From the back of a room, the class reads the disc before the digits.

Keep the board awake while the timer runs

While the countdown runs, the page asks the browser to keep the screen awake. Most current desktop browsers support this. The browsers built into some panels do not.

Many panels also have their own power-saving setting that dims or switches off the screen after a few minutes without touch. That setting sits below the browser, and a web page cannot change it. If the board goes dark during a 20-minute countdown, look in the panel's settings for a sleep timer or an eco mode, and give it a longer delay.

Let a student run the timer

On a touch board, a student can start the timer for the class. That frees you to stay with a group. It also gives one student a small job with a clear rule.

Show the timekeeper three things: tap the length, tap Start, and tap Start again (now labeled Pause) only when you say so. Ask them not to use − and + without you. The countdown is a promise to the whole class, and it should not change in silence.

During my PhD, I ran workshops in a room with a touch display. When I let a participant start the timer for each exercise, I could stay at the back of the room. I saw much more of what the groups were doing than when I stood at the board.

The classroom picture behind the timer

The picture is an empty classroom at golden hour: sun through tall windows, plants on the windowsill, wooden desks, bookshelves, string lights and a green chalkboard. On a large panel, the picture fills the screen, and the disc sits in front of the painted chalkboard. The digits are light, so they stay readable on the darker parts of the picture.

This picture was made for this page. It is not one of the scenes in the Fwocus app. The app has more than 60 scenes of its own and is for your own work, not the board: planning and marking in timed sessions, with a task list, notes, saved sessions and focus stats.

FAQ

Do I need to install an app on the smartboard?

No. The timer runs in any current web browser, either the board's own browser or the browser on the connected computer. There is no account and nothing to install.

Does the timer work without a keyboard?

Yes. Every function has a button: the preset tabs, −, +, Start, reset and fullscreen. If you do have a keyboard, Space starts and pauses, R resets, F switches fullscreen, and the arrow keys add or remove a minute.

Can I use the timer and my lesson slides at the same time?

Yes, if your board shows two windows side by side. Put the timer in a narrow window next to the slides. The disc keeps its size as long as the window has its full height.

What happens when the time is up?

A soft singing-bowl chime plays, the disc is empty, the digits turn red and pulse, and "Time's up" appears. Tap Restart to run the same length again, or tap a tab to choose a new one.